Contact Us
SalesDept@heisener.com 0755-83210559 ext. 805

IMD6AT108

hotIMD6AT108

IMD6AT108

For Reference Only

Part Number IMD6AT108
Manufacturer Rohm Semiconductor
Description TRANS NPN/PNP PREBIAS 0.3W SMT6
Datasheet IMD6AT108 Datasheet
Package SC-74, SOT-457
In Stock 207,126 piece(s)
Unit Price $ 0.0990 *
Lead Time Can Ship Immediately
Estimated Delivery Time Sep 27 - Oct 2 (Choose Expedited Shipping)
Request for Quotation

Part Number # IMD6AT108 (Transistors - Bipolar (BJT) - Arrays, Pre-Biased) is manufactured by Rohm Semiconductor and distributed by Heisener. Being one of the leading electronics distributors, we carry many kinds of electronic components from some of the world’s top class manufacturers. Their quality is guaranteed by its stringent quality control to meet all required standards.

For IMD6AT108 specifications/configurations, quotation, lead time, payment terms of further enquiries please have no hesitation to contact us. To process your RFQ, please add IMD6AT108 with quantity into BOM. Heisener.com does NOT require any registration to request a quote of IMD6AT108.

IMD6AT108 Specifications

ManufacturerRohm Semiconductor
CategoryDiscrete Semiconductor Products - Transistors - Bipolar (BJT) - Arrays, Pre-Biased
Datasheet IMD6AT108Datasheet
PackageSC-74, SOT-457
Series-
Transistor Type1 NPN, 1 PNP - Pre-Biased (Dual)
Current - Collector (Ic) (Max)100mA
Voltage - Collector Emitter Breakdown (Max)50V
Resistor - Base (R1) (Ohms)4.7k
Resistor - Emitter Base (R2) (Ohms)-
DC Current Gain (hFE) (Min) @ Ic, Vce100 @ 1mA, 5V
Vce Saturation (Max) @ Ib, Ic300mV @ 250µA, 5mA
Current - Collector Cutoff (Max)500nA (ICBO)
Frequency - Transition250MHz
Power - Max300mW
Mounting TypeSurface Mount
Package / CaseSC-74, SOT-457
Supplier Device PackageSMT6

IMD6AT108 Datasheet

Page 1

Page 2

EMD6 / UMD6N / IMD6A General purpose (dual digital transistor) Datasheet lOutline Parameter Value SOT-563 SOT-363 VCEO 50V     IC 100mA R1 4.7kΩ EMD6 UMD6N     (EMT6) (UMT6) SOT-457                       Parameter Value     VCEO -50V   IC -100mA   R1 4.7kΩ IMD6A       (SMT6)                         lFeatures lInner circuit 1)Both the DTA143T chip and DTC143T   chip in an EMT or UMT or SMTpackage. 2)Mounting possible with EMT3 or UMT3   or SMT3 automatic mounting machines. 3)Transistor elements are independent,   eliminating interference. 4)Mounting cost and area can be cut in half. EMD6 / UMD6N IMD6A lApplication INVERTER, INTERFACE, DRIVER lPackaging specifications             Part No. Package Package size Taping code Reel size (mm) Tape width (mm) Basic ordering unit.(pcs) Marking EMD6 SOT-563 (EMT6) 1616 T2R 180 8 8000 D6 UMD6N SOT-363 (UMT6) 2021 TR 180 8 3000 D6 IMD6A SOT-457 (SMT6) 2928 T108 180 8 3000 D6                                                                                           www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 1/7 20151029 - Rev.003

Page 3

EMD6 / UMD6N / IMD6A Datasheet lAbsolute maximum ratings (Ta = 25°C) Parameter Symbol DTr1(NPN) DTr2(PNP) Unit Collector-base voltage VCBO 50 -50 V Collector-emitter voltage VCEO 50 -50 V Emitter-base voltage VEBO 5 -5 V Collector current IC 100 -100 mA Power dissipation EMD6/ UMD6N PD *1*2 150 mW/Total IMD6A PD *1*3 300 Junction temperature Tj 150 ℃ Range of storage temperature Tstg -55 to +150 ℃ lElectrical characteristics (Ta = 25°C) Parameter Symbol Conditions Values Unit Min. Typ. Max. Collector-base breakdown voltage BVCBO IC = 50μA 50 - - V Collector-emitter breakdown voltage BVCEO IC = 1mA 50 - - V Emitter-base breakdown voltage BVEBO IE = 50μA 5 - - V Collector cut-off current ICBO VCB = 50V - - 500 nA Emitter cut-off current IEBO VEB = 4V - - 500 nA Collector-emitter saturation voltage VCE(sat) IC = 5mA, IB = 0.25mA - - 300 mV DC current gain hFE VCE = 5V, IC = 1mA 100 250 600 - Input resistance R1 - 3.29 4.7 6.11 kΩ Transition frequency fT *4 VCE = 10V, IE = -5mA, f = 100MHz - 250 - MHz lElectrical characteristics (Ta = 25°C) Parameter Symbol Conditions Values Unit Min. Typ. Max. Collector-base breakdown voltage BVCBO IC = -50μA -50 - - V Collector-emitter breakdown voltage BVCEO IC = -1mA -50 - - V Emitter-base breakdown voltage BVEBO IE = -50μA -5 - - V Collector cut-off current ICBO VCB = -50V - - -500 nA Emitter cut-off current IEBO VEB = -4V - - -500 nA Collector-emitter saturation voltage VCE(sat) IC = -5mA, IB = -0.25mA - - -300 mV DC current gain hFE VCE = -5V, IC = -1mA 100 250 600 - Input resistance R1 - 3.29 4.7 6.11 kΩ Transition frequency fT *4 VCE = -10V, IE = 5mA, f = 100MHz - 250 - MHz *1 Each terminal mounted on a reference land. *2 120mW per element must not be exceeded. *3 200mW per element must not be exceeded. *4 Characteristics of built-in transistor. www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 2/7 20151029 - Rev.003

Page 4

EMD6 / UMD6N / IMD6A       Datasheet lElectrical characteristic curves(Ta = 25°C) Fig.1 Grounded emitter propergation     characteristics Fig.2 Grounded emitter output     characteristics Fig.3 DC current gain vs. collector current Fig.4 Collector-emitter saturation voltage     vs. collector current                                                                                             www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 3/7 20151029 - Rev.003

Page 5

EMD6 / UMD6N / IMD6A       Datasheet lElectrical characteristic curves(Ta = 25°C) Fig.1 Grounded emitter propergation     characteristics Fig.2 Grounded emitter output     characteristics Fig.3 DC current gain vs. collector current Fig.4 Collector-emitter saturation voltage     vs. collector current                                                                                             www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 4/7 20151029 - Rev.003

Page 6

EMD6 / UMD6N / IMD6A       Datasheet lDimensions                                                                                             www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 5/7 20151029 - Rev.003

Page 7

EMD6 / UMD6N / IMD6A       Datasheet lDimensions                                                                                             www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 6/7 20151029 - Rev.003

Page 8

EMD6 / UMD6N / IMD6A       Datasheet lDimensions                                                                                             www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 7/7 20151029 - Rev.003

Page 9

Datasheet Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved. Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification

Page 10

Datasheet Notice-PGA-E Rev.001 © 2015 ROHM Co., Ltd. All rights reserved. Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties.

IMD6AT108 Reviews

Average User Rating
5 / 5 (166)
★ ★ ★ ★ ★
5 ★
149
4 ★
17
3 ★
0
2 ★
0
1 ★
0

Write a Review

Not Rated
Thanks for Your Review!

Lil*****ance

August 22, 2020

Comparison with other company, Heisener is my first choice for supplier.

Jos*****ells

August 17, 2020

Easy transaction. Very pleased with goods in perfect condition would recommend Heisener company.

Haye*****msey

August 10, 2020

Diodes okay. Shipped quick and received with well - packed

Nata*****Dani

July 28, 2020

Very good and very fast . 100% safe company

Fait*****ndolph

July 26, 2020

I have never been experienced anything wrong with my order, the logistic has always get out the same day, and the items are always well packaged.

Chan*****hields

July 20, 2020

I received technical certification with a good staff. They have good fair prices on brand names.

Elea*****Sarkar

July 15, 2020

A convenient and small package. I have used 2 of the 10 units so far and they work fine.

Bri*****Gour

July 12, 2020

Your prices are low and your website is customer-use friendly.

Nala*****taker

July 10, 2020

Very professional sellers, they have adopted MSL packaging for different parts.

Gise*****Steele

July 10, 2020

I got a very helpful customer service here. Definitely will order my electronics needs again.

IMD6AT108 Guarantees

Service Guarantee

Service Guarantees

We guarantee 100% customer satisfaction.

Our experienced sales team and tech support team back our services to satisfy all our customers.

Quality Guarantee

Quality Guarantees

We provide 90 days warranty.

If the items you received were not in perfect quality, we would be responsible for your refund or replacement, but the items must be returned in their original condition.

IMD6AT108 Packaging

Verify Products
Customized Labels
Professional Packaging
Sealing
Packing
Insepction

IMD6AT108 Related Products

SIT8209AC-3F-28E-166.000000X SIT8209AC-3F-28E-166.000000X SiTIME, -20 TO 70C, 5032, 10PPM, 2.8V, 1, -, - View
1825Y0630472JCT 1825Y0630472JCT Knowles Syfer, CAP CER 4700PF 63V C0G/NP0 1825, 1825 (4564 Metric), - View
STGIPS10C60-H STGIPS10C60-H STMicroelectronics, MOD IPM SLLIMM 10A 600V 25SDIP, 25-PowerDIP Module (0.993", 25.23mm), - View
MAX6316LUK31CY-T MAX6316LUK31CY-T Maxim Integrated, IC MPU/RESET CIRC 3.08V SOT23-5, SC-74A, SOT-753, - View
ATA663211-FAQW ATA663211-FAQW Microchip Technology, TXRX LIN SBC 8DFN, 8-VDFN Exposed Pad, - View
DSPIC33FJ64GP306T-I/PT DSPIC33FJ64GP306T-I/PT Microchip Technology, IC MCU 16BIT 64KB FLASH 64TQFP, 64-TQFP, - View
hotSTM32F102R6T6A STM32F102R6T6A STMicroelectronics, IC MCU 32BIT 32KB FLASH 64LQFP, 64-LQFP, - View
hotCY39100V388B-200MGXC CY39100V388B-200MGXC Cypress Semiconductor Corp, IC CPLD 1536MC 7.5NS 388BGA, 388-BGA, - View
RWR84S25R5FRS73 RWR84S25R5FRS73 Vishay Dale, RES 25.5 OHM 7W 1% WW AXIAL, Axial, - View
RNC55K82R5FSBSL RNC55K82R5FSBSL Vishay Dale, RES 82.5 OHM 1/8W 1% AXIAL, Axial, - View
RMCP2010FT390K RMCP2010FT390K Stackpole Electronics Inc., RES SMD 390K OHM 1% 1W 2010, 2010 (5025 Metric), - View
SCDA10000T-48-Y1 SCDA10000T-48-Y1 Cosel USA, Inc., 10KW AC/DC PS, -, - View
Payment Methods
Delivery Services

Quick Inquiry

IMD6AT108

Certified Quality

Heisener's commitment to quality has shaped our processes for sourcing, testing, shipping, and every step in between. This foundation underlies each component we sell.

ISO9001:2015, ICAS, IAF, UKAS

View the Certificates

Do you have any question about IMD6AT108?

0755-83210559 ext. 805 SalesDept@heisener.com heisener007 3008774228 Send Message

IMD6AT108 Tags

  • IMD6AT108
  • IMD6AT108 PDF
  • IMD6AT108 datasheet
  • IMD6AT108 specification
  • IMD6AT108 image
  • Rohm Semiconductor
  • Rohm Semiconductor IMD6AT108
  • buy IMD6AT108
  • IMD6AT108 price
  • IMD6AT108 distributor
  • IMD6AT108 supplier
  • IMD6AT108 wholesales

IMD6AT108 is Available in