S6065KTP

Page 1

Page 2

305©2010 Littelfuse, Inc Revised: May 10, 2010 09:33 PM Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Sxx65x & Sxx70x Series 65 / 70 Amp Standard SCRs 6 5 /7 0 A S C R s Sxx65x & Sxx70x Series Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits junctions to 1000 V 950 A Schematic Symbol Main Features Symbol Value Unit I T(RMS) 65 & 70 A V DRM /V RRM 400 to 1000 V I GT 50 mA Absolute Maximum Ratings Symbol Parameter Test Conditions Value Unit I T(RMS) RMS on-state current Sxx65J Sxx65K T C = 75°C 65 A Sxx70W T C = 80°C 70 I T(AV) Average on-state current Sxx65J Sxx65K TC = 75°C 41.0 A Sxx70W T C = 80°C 45.0 A I TSM Peak non-repetitive surge current single half cycle; f = 50Hz; T J (initial) = 25°C 800 A single half cycle; f = 60Hz; T J (initial) = 25°C 950 I2t I2t Value for fusing t p = 8.3 ms 3745 A2s di/dt Critical rate of rise of on-state current f = 60Hz ; T J = 125°C 200 A/μs I GM Peak gate current T J = 125°C P W = μS 5.0 A P G(AV) Average gate power dissipation T J = 125°C 1.0 W T stg Storage temperature range -40 to 150 °C T J Operating junction temperature range -40 to 125 °C Applications Typical applications are AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. A K G Agency Approval Agency Agency File Number ® J & K Packages: E71639 ®

Page 3

306 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 65 / 70 Amp Standard SCRs Sxx65x & Sxx70x Series Electrical Characteristics (T J = 25°C, unless otherwise specified) Symbol Test Conditions Value Unit I GT V D = 12V; R L = 30 MAX. 50 mA MIN. 5 V GT MAX. 2.0 V dv/dt V D = V DRM ; gate open; T J = 100°C 400V MIN. 650 V/μs 600V 600 800V 500 1000V 250 V D = V DRM ; gate open; T J = 125°C 400V 550 600V 500 800V 475 V GD V D = V DRM ; R L = 3.3 k ; T J = 125°C MIN. 0.2 V I H I T = 400mA (initial) MAX. 80 mA t q (1) MAX. 35 μs t gt I G = 2 x I GT ; PW = 15μs; I T = 140A TYP. 2.5 μs Note : (1) I T =2A; t p =50μs; dv/dt=5V/μs; di/dt=-30A/μs Thermal Resistances Symbol Parameter Value Unit R (J-C) Junction to case (AC) Sxx65J Sxx65K 0.86 °C/W Sxx70W 0.6 Note: xx = voltage Static Characteristics Symbol Test Conditions Value Unit V TM 65A Device I T = 130A; t p = 380μs MAX. 1.8 V 70A Device I T = 140A; t p = 380μs I DRM / I RRM V DRM / V RRM T J = 25°C 400 – 800V MAX. 20 μA 1000 V 30 T J = 100°C 400 – 600V 1500 800V 2000 1000V 5000 T J = 125°C 400V – 600V 3000 800V 5000

Page 4

307©2010 Littelfuse, Inc Revised: May 10, 2010 09:33 PM Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Sxx65x & Sxx70x Series 65 / 70 Amp Standard SCRs 6 5 /7 0 A S C R s Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 R a ti o o f I G T / I G T ( T J = 2 5 °C ) Junction Temperature (T J ) -- (°C) 125 Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: On-State Current vs. On-State Voltage (Typical) 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 R a ti o o f V G T / V G T ( T J = 2 5 °C ) Junction Temperature (T J ) -- (°C) 125 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 R a ti o o f I H / I H ( T J = 2 5 °C ) Junction Temperature (T J ) -- (°C) 125 0 20 40 60 80 100 120 140 160 180 200 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 In s ta n ta n e o u s O n -s ta te C u rr e n t (i T ) – A m p s Instantaneous On-state Voltage (v T ) – Volts T J = 25°C 0 10 20 30 40 50 60 0 10 20 30 40 50 60 70 A v e ra g e O n -S ta te P o w e r D is s ip a ti o n [P D ( A V )] - ( W a tt s ) RMS On-State Current [I T(R MS) ] - (Am ps) 70 75 80 85 90 95 100 105 110 115 120 125 130 0 10 20 30 40 50 60 70 80 M a x im u m A ll o w a b le C a s e T e m p e ra tu re (T C )- °C RMS On-State Current [I T(RMS) ] - Amps Sxx70W Sxx65K Sxx65J CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° The "K" package rating with its narrow leads is intended for high surge condition use only and not recom- mended for >50A rms continuous current use since lead temperature depending on lead length can exceed PCB solder melting temperature. "J" or "W" packages are recommended for >50A rms continuous current require- ments. Note: xx = voltage

Page 5

308 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 65 / 70 Amp Standard SCRs Sxx65x & Sxx70x Series Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current 70 75 80 85 90 95 100 105 110 115 120 125 130 0 5 10 15 20 25 30 35 40 45 50 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° Sxx65K Sxx65J M a x im u m A ll o w a b le C a s e T e m p e ra tu re (T C ) - °C Average On-State Current [I T(AVE) ] - Amps Sxx70W The "K" package rating with its narrow leads is intended for high surge condition use only and not recommended for >32A (AV) continuous current use since lead temperature depending on lead length can exceed PCB solder melting temperature. "J" or "W" packages are recommended for >32A (AV) continu- ous current requirements. 10 100 1000 1 10 100 1000 Sxx65K Sxx65J Sxx70W Surge Current Duration -- Full Cycles P e a k S u rg e ( N o n -r e p e ti ti v e ) O n -s ta te C u rr e n t (I T S M ) – A m p s Figure 10: Surge Peak On-State Current vs. Number of Cycles SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [I T(RMS) ]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. Figure 8: Peak Capacitor Discharge Current Figure 9: Peak Capacitor Discharge Current Derating 100 1000 10000 0.5 1.0 10.0 50.0 P e a k D is ch a rg e C u rr e n t (I T M ) - A m p s Pulse Current Duration (t w ) - ms I TRM t W 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 25 50 75 100 125 150 N o rm a li ze d P e a k C u rr e n t Case Temperature (T C ) - °C Note: xx = Voltage

Page 6

309©2010 Littelfuse, Inc Revised: May 10, 2010 09:33 PM Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Sxx65x & Sxx70x Series 65 / 70 Amp Standard SCRs 6 5 /7 0 A S C R s Soldering Parameters Reflow Condition Pb – Free assembly Pre Heat - Temperature Min (T s(min) ) 150°C - Temperature Max (T s(max) ) 200°C - Time (min to max) (t s ) 60 – 180 secs Average ramp up rate (Liquidus Temp) (T L ) to peak 5°C/second max T S(max) to T L - Ramp-up Rate 5°C/second max Reflow - Temperature (T L ) (Liquidus) 217°C - Temperature (t L ) 60 – 150 seconds Peak Temperature (T P ) 260+0/-5 °C Time within 5°C of actual peak Temperature (t p ) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (T P ) 8 minutes Max. Do not exceed 280°C Physical Specifications Environmental Specifications Test Specifications and Conditions AC Blocking MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours Temperature Cycling MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time Temperature/ Humidity EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity High Temp Storage MIL-STD-750, M-1031, 1008 hours; 150°C Low-Temp Storage 1008 hours; -40°C Thermal Shock MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature Autoclave EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Terminal Finish 100% Matte Tin-plated Body UL recognized epoxy meeting flammability classification 94V-0 Lead Material Copper Alloy Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Time T e m p e ra tu re TP TL TS(max) TS(min) 25 tP tL tS time to peak temperature Preheat Ramp-up Ramp-down

Page 7

310 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 65 / 70 Amp Standard SCRs Sxx65x & Sxx70x Series Dimensions – TO-218X (W Package) — Non-Isolated Mounting Tab Dimensions – TO-218AC (K Package) — Isolated Mounting Tab Dimension Inches Millimeters Min Max Min Max A 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 F 0.635 0.655 16.13 16.64 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 J 0.575 0.625 14.61 15.88 K 0.256 0.264 6.50 6.71 L 0.220 0.228 5.58 5.79 M 0.080 0.088 2.03 2.24 N 0.169 0.177 4.29 4.49 P 0.034 0.042 0.86 1.07 R 0.113 0.121 2.87 3.07 S 0.086 0.096 2.18 2.44 T 0.156 0.166 3.96 4.22 U 0.164 0.165 4.10 4.20 V 0.603 0.618 15.31 15.70 W 0.000 0.005 0.00 0.13 X 0.003 0.012 0.07 0.30 Y 0.028 0.032 0.71 0.81 Z 0.085 0.095 2.17 2.42 G R Y H D C K B A E F N T M P J L S V U (diameter) W X CATHODE ANODE ANODE Tc Measurement Point GATE Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Z Dimension Inches Millimeters Min Max Min Max A 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 F 0.635 0.655 16.13 16.64 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 J 0.575 0.625 14.61 15.88 K 0.211 0.219 5.36 5.56 L 0.422 0.437 10.72 11.10 M 0.058 0.068 1.47 1.73 N 0.045 0.055 1.14 1.40 P 0.095 0.115 2.41 2.92 Q 0.008 0.016 0.20 0.41 R 0.008 0.016 0.20 0.41 U 0.164 0.165 4.10 4.20 W 0.085 0.095 2.17 2.42 C D H G F B A E Tc Measurement Point U (diameter) P GATE J ANODE CATHODE M N K L R Q Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). W

Page 8

311©2010 Littelfuse, Inc Revised: May 10, 2010 09:33 PM Teccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Sxx65x & Sxx70x Series 65 / 70 Amp Standard SCRs 6 5 /7 0 A S C R s Dimensions – TO-218X (J Package) — Isolated Mounting Tab Common with Center Lead Dimension Inches Millimeters Min Max Min Max A 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 F 0.635 0.655 16.13 16.64 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 J 0.575 0.625 14.61 15.88 K 0.256 0.264 6.50 6.71 L 0.220 0.228 5.58 5.79 M 0.080 0.088 2.03 2.24 N 0.169 0.177 4.29 4.49 P 0.034 0.042 0.86 1.07 R 0.113 0.121 2.87 3.07 S 0.086 0.096 2.18 2.44 T 0.156 0.166 3.96 4.22 U 0.164 0.165 4.10 4.20 V 0.603 0.618 15.31 15.70 W 0.000 0.005 0.00 0.13 X 0.003 0.012 0.07 0.30 Y 0.028 0.032 0.71 0.81 Z 0.085 0.095 2.17 2.42 Product Selector Part Number Voltage Gate Sensitivity Type Package 400V 600V 800V 1000V Sxx65K X X X X 50mA Standard SCR TO-218AC Sxx65J X X X 50mA Standard SCR TO-218X Sxx70W X X X 50mA Standard SCR TO-218X Note: xx = Voltage Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx65KTP Sxx65K 4.40g Tube 250 (25 per tube) Sxx65JTP Sxx65J 5.23g Tube 250 (25 per tube) Sxx70WTP Sxx70W 5.23g Tube 250 (25 per tube) Note: xx = Voltage G R Y H D C K B A E F N T M P J L S V U (diameter) W X CATHODE Tc Measurement Point GATE Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Z ANODE