Contact Us +86-755-83210559 ext. 811




For Reference Only

Part Number MAX1735EUK25+T
Manufacturer Maxim Integrated
Description IC REG LIN NEG ADJ 200MA SOT23-5
Datasheet MAX1735EUK25+T Datasheet
Package SC-74A, SOT-753
In Stock 5,640 piece(s)
Unit Price $ 1.3831 *
Lead Time Can Ship Immediately
Estimated Delivery Time Aug 10 - Aug 15 (Choose Expedited Shipping)
Request for Quotation

Part Number # MAX1735EUK25+T (PMIC - Voltage Regulators - Linear) is manufactured by Maxim Integrated and distributed by Heisener. Being one of the leading electronics distributors, we carry many kinds of electronic components from some of the world’s top class manufacturers. Their quality is guaranteed by its stringent quality control to meet all required standards.

For MAX1735EUK25+T specifications/configurations, quotation, lead time, payment terms of further enquiries please have no hesitation to contact us. To process your RFQ, please add MAX1735EUK25+T with quantity into BOM. does NOT require any registration to request a quote of MAX1735EUK25+T.

MAX1735EUK25+T Specifications

ManufacturerMaxim Integrated
CategoryIntegrated Circuits (ICs) - PMIC - Voltage Regulators - Linear
Datasheet MAX1735EUK25+TDatasheet
PackageSC-74A, SOT-753
Output ConfigurationNegative
Output TypeAdjustable (Fixed)
Number of Regulators1
Voltage - Input (Max)-6.5V
Voltage - Output (Min/Fixed)-1.25V (-2.5V)
Voltage - Output (Max)-5.5V
Voltage Dropout (Max)0.24V @ 200mA
Current - Output200mA
Current - Quiescent (Iq)-
Current - Supply (Max)85µA ~ 125µA
PSRR60dB (100Hz)
Control FeaturesEnable
Protection FeaturesOver Current, Over Temperature, Short Circuit
Operating Temperature-40°C ~ 85°C
Mounting TypeSurface Mount
Package / CaseSC-74A, SOT-753
Supplier Device PackageSOT-23-5

MAX1735EUK25+T Datasheet

Page 1

Page 2

General Description The MAX1735 negative-output, low-dropout linear regu- lator operates from a -2.5V to -6.5V input and delivers a guaranteed 200mA with a low 80mV dropout. The high- accuracy (±1%) output voltage is preset or can be adjusted from -1.25V to -5.5V with an external resistive voltage-divider. An internal N-channel MOSFET allows for a low 85µA quiescent current virtually independent of the load, making this device ideal for battery-powered portable equipment, such as PDAs, mobile phones, cordless phones, and wireless data modems. The device is available in several preset output voltage versions: -5.0V, -3.0V, and -2.5V. All versions offer a 1nA low-power shutdown mode, short-circuit protec- tion, and thermal overload protection. The device is offered in a tiny 5-pin SOT23 package. Applications Disk Drives Modems Instrumentation Amplifiers Notebook Computers Mobile and Cordless Telephones PCMCIA Cards GaAsFET Bias Mobile Wireless Data Modems PDAs and Palmtop Computers Features  Guaranteed 200mA Output Current  Low 80mV Dropout Voltage at 200mA  Low 85µA Quiescent Supply Current  Low 1nA Current Shutdown Mode  Stable with 1µF COUT  PSRR >60dB at 100Hz  Thermal Overload Protection  Short-Circuit Protection  -5.0V, -3.0V, or -2.5V Output Voltage or Adjustable (-1.25V to -5.5V)  Tiny SOT23-5 Package M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 ________________________________________________________________ Maxim Integrated Products 1 IN SETSHDN 1 5 OUTGND MAX1735 SOT23-5 TOP VIEW 2 3 4 MAX1735 SHDN -6.5V TO -2.5V INPUT -5V, -3V, OR -2.5V OUTPUT UP TO 200mA CIN COUT OUTIN SET GND GND ON OFF ON Typical Operating Circuit 19-1783; Rev 1; 11/03 Pin Configuration Ordering Information PART TEMP RANGE PIN- PACKAGE MAX1735EUK50-T -40°C to +85°C 5 SOT23-5 MAX1735EUK30-T -40°C to +85°C 5 SOT23-5 MAX1735EUK25-T -40°C to +85°C 5 SOT23-5 Output-Voltage Selector Guide PART PRESET OUTPUT VOLTAGE SOT TOP MARK MAX1735EUK50-T -5.0V or adj ADOZ MAX1735EUK30-T -3.0V or adj ADOY MAX1735EUK25-T -2.5V or adj ADOX For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at

Page 3

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 2 _______________________________________________________________________________________ ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS (Circuit of Figure 2, VIN = VOUT - 1V, VSHDN = VIN, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. IN, SET to GND .................................................... -7.0V to +0.3V SHDN to GND ............................................ (VIN - 0.3)V to +7.0V OUT to GND ...............................................(VIN - 0.3)V to +0.3V Output Short-Circuit Duration ........................................Indefinite Continuous Power Dissipation (TA = +70°C) 5-Pin SOT23 (derate 7.1mW/°C above +70°C)........... 571mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range ............................ -65°C to +150°C Lead Temperature (soldering, 10s) ................................ +300°C PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Input Voltage VIN -6.5 -2.5 V TA = +25°C, IOUT = -100µA -1 +1 IOUT = -100µA, TA = 0°C to +85°C -2 +2Output Voltage Accuracy ILOAD = -100µA to -200mA -3 +2 % Circuit of Figure 3, TA = +25°C, IOUT = -100µA -1.2625 -1.25 -1.2375 Circuit of Figure 3, IOUT = -100µA, TA = 0°C to +85°C -1.275 -1.225SET Regulation Set Point Circuit of Figure 3, ILOAD = -100µA to -200mA -1.275 -1.2125 V Maximum Output Current IOUT -200 mA Current Limit ILIM VOUT = 0 -1020 -515 -250 mA IOUT = -100µA -180 -85 Ground-Pin Current IQ IOUT = -200mA -125 µA IOUT = -100mA 40 Dropout Voltage (Note 2) IOUT = -200mA 80 240 mV Line Regulation Circuit of Figure 3, VIN from -6.5V to -2.5V, VOUT = -1.25V -0.15 0 +0.15 %/V Load Regulation IOUT from 0mA to -200mA 0.004 %/mA Output Voltage Noise 10Hz to 1MHz, COUT = 1µF 160 µVRMS Power-Supply Rejection Ratio PSRR f = 100Hz 60 dB TA = +25°C -1 -0.001 Shutdown Supply Current V SHDN = 0 TA = +85°C -1 µA Positive voltage at SHDN +1.6SHDN Input High Threshold (Note 3) Negative voltage at SHDN -1.6 V Positive voltage at SHDN +0.4SHDN Input Low Threshold (Note 3) Negative voltage at SHDN -0.4 V Set Input Bias Current ISET VSET = -1.25V, TA = +25°C -100 -15 nA V SHDN = +6.5V 3.5 SHDN Input Bias Current TA = +25°C V SHDN = 0, -6.5V -0.5 +0.5 µA Thermal Shutdown Junction Temperature Hysteresis = 15°C (typ) 160 °C Note 1: Limits are 100% production tested at TA = +25°C. Limits over operating temperature range are guaranteed by design. Note 2: The dropout voltage is defined as VOUT - VIN, when VOUT is 100mV above the nominal value of VOUT. Note 3: The SHDN logic input can be driven by either a positive voltage or a negative voltage. | VSHDN | < 0.4V puts the device in shutdown, while | VSHDN | > 1.6V enables the device.

Page 4

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 _______________________________________________________________________________________ 3 0 40 20 100 80 60 160 140 120 180 0 -2 -3-1 -4 -5 -6 SUPPLY CURRENT vs. SUPPLY VOLTAGE M A X 1 7 3 5 t o c0 1 SUPPLY VOLTAGE (V) S U P P LY C U R R EN T (µ A ) ILOAD = 200mA -7 70 90 80 110 100 130 120 140 0 8040 120 16020 10060 140 180 200 SUPPLY CURRENT vs. LOAD CURRENT M A X 1 7 3 5 t o c0 2 LOAD CURRENT (mA) S U P P LY C U R R EN T (µ A ) 0 40 20 100 80 60 160 140 120 180 -40 10-15 35 60 85 SUPPLY CURRENT vs. TEMPERATURE M A X 1 7 3 5 t o c0 3 TEMPERATURE (°C) S U P P LY C U R R EN T (µ A ) NO LOAD ILOAD = 200mA 0 20 60 40 80 100 0 50 7525 100 125 150 175 200 DROPOUT VOLTAGE vs. LOAD CURRENT M A X 1 7 3 5 t o c0 4 LOAD CURRENT (mA) D R O P O U T V O LT A G E (m V ) TA = +25°C TA = +85°C TA = -40°C VOUT = -2.9V -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0 0 5025 75 100 125 150 175 200 OUTPUT VOLTAGE CHANGE vs. LOAD CURRENT M A X 1 7 3 5 t o c0 5 LOAD CURRENT (mA) O U TP U T V O LT A G E C H A N G E (% ) VOUT = -3V TA = -40°C TA = +25°C TA = +85°C -1.00 -0.75 -0.50 -0.25 0 0.25 0.50 0.75 1.00 -40 -15 10 35 60 85 OUTPUT VOLTAGE CHANGE vs. TEMPERATURE M A X 1 7 3 5 t o c0 6 TEMPERATURE (°C) O U TP U T V O LT A G E C H A N G E (% ) ILOAD = 200mA NO LOAD Typical Operating Characteristics (Circuit of Figure 2, VIN = -4.0V, VOUT = -3.0V, TA = +25°C, unless otherwise specified.)

Page 5

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 4 _______________________________________________________________________________________ 0.001 0.01 0.1 1 10 100 0 80 10040 6020 120 140 160 180 200 REGION OF STABLE ESR vs. LOAD CURRENT M A X 1 7 3 5 t o c1 0 LOAD CURRENT (mA) R EG IO N O F S TA B LE E S R C O U T (Ω ) COUT = 1µF REGION OF STABILITY LINE-TRANSIENT RESPONSE MAX1735 toc11 TIME (100µs/div) VOUT 50mV/div VIN 1V/div LOAD-TRANSIENT RESPONSE (NORMAL OPERATION) MAX1735 toc12 TIME (100µs/div) ILOAD STEP 0 to 50mA VOUT 10mV/div LOAD-TRANSIENT RESPONSE (NEAR DROPOUT) MAX1735 toc13 TIME (100µs/div) ILOAD STEP 0 to 50mA VOUT 10mV/div Typical Operating Characteristics (continued) (Circuit of Figure 2, VIN = -4.0V, VOUT = -3.0V, TA = +25°C, unless otherwise specified.) 0 20 10 40 30 60 50 70 1 10010 1k 10k 100k POWER-SUPPLY REJECTION RATIO vs. FREQUENCY M A X 1 7 3 5 t o c0 7 FREQUENCY (Hz) P S R R ( dB ) 1M COUT = 10µF COUT = 1.0µF 10 0.01 10 1k 100k OUTPUT NOISE DENSITY vs. FREQUENCY M A X 1 7 3 5 t o c0 8 FREQUENCY (Hz) O U TP U T N O IS E (µ V R M S /√ H z) 0.1 1 OUTPUT NOISE (10Hz TO 1MHz) M A X 1 7 3 5 t o c0 9 TIME (1ms/div) 500µV/div COUT = 1µF ILOAD = 50mA

Page 6

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 _______________________________________________________________________________________ 5 SHUTDOWN RESPONSE (DRIVEN FROM A POSITIVE VOLTAGE) MAX1735 toc14a TIME (200µs/div) VSHDN 2V/div 0 VOUT 2V/div 0 SHUTDOWN RESPONSE (DRIVEN BY A NEGATIVE VOLTAGE) MAX1735 toc14b TIME (200µs/div) VSHDN 2V/div VOUT 2V/div 0 0 -0.5 0 0.5 1.0 1.5 2.0 -6.5 -2.0 -0.5-5.0 -3.5 1.0 2.5 4.0 5.5 SHUTDOWN-PIN BIAS CURRENT vs. SHUTDOWN-PIN VOLTAGE M A X 1 7 3 5 t o c1 5 SHUTDOWN-PIN VOLTAGE (V) S H U TD O W N -P IN B IA S C U R R EN T (µ A ) IN V A LI D L O G IC V O LT A G E IN V A LI D L O G IC V O LT A G E Pin Description PIN NAME FUNCTION 1 GND Ground 2 IN Regulator Input. Supply voltage can range from -2.5V to -6.5V. Bypass with a 1µF capacitor to GND (see Capacitor Selection and Regulator Stability). This pin also functions as a heatsink. Solder to a large PC board pad or directly to the PC board power plane to maximize thermal dissipation. 3 SHDN Shutdown Input. Drive SHDN to GND to turn the regulator off, reducing the input current to less than 1nA. Drive SHDN above +1.6V or below -1.6V to enable the regulator. Connect SHDN to IN for always-on operation. 4 SET Dual Mode™ Regulator Feedback Input. Connect SET to GND for the preset output voltage. Use a resistive voltage-divider from OUT to SET to set the output voltage between -1.25V and -5.5V. Regulation setpoint is -1.25V. 5 OUT Regulator Output. OUT supplies up to 200mA in regulation. Bypass to GND with a 1µF ceramic capacitor. Typical Operating Characteristics (continued) (Circuit of Figure 2, VIN = -4.0V, VOUT = -3.0V, TA = +25°C, unless otherwise specified.) Dual Mode is a trademark of Maxim Integrated Products, Inc.

Page 7

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 Detailed Description The MAX1735 is a low-dropout negative linear voltage regulator. It features Dual Mode operation, allowing a fixed -5.0V, -3.0V, or -2.5V output voltage or an adjustable output from -1.25V to -5.5V. The regulator is guaranteed to supply 200mA of output current. It fea- tures 60dB power-supply rejection for noise-sensitive applications and a low 85µA operating current that opti- mizes it for battery-operated devices. As Figure 1 illustrates, the device consists of an internal -1.25V reference, an error amplifier, an N-channel MOSFET, an internal precision-trimmed feedback volt- age-divider, and a Dual Mode comparator. The -1.25V reference is connected to the inverting input of the error amplifier. The error amplifier compares the reference voltage with the selected feedback voltage and amplifies the difference. The error amplifier drives the MOSFET to control the output voltage. The feedback voltage for regulation is generated by either an internal or external resistive voltage-divider connected from OUT to SET. The internal Dual Mode comparator selects the feedback path based on VSET. Connect SET to GND to use the internal feedback path, setting the output voltage to the preset value. If an external voltage-divider is used, see Output Voltage Selection. Internal N-Channel MOSFET The MAX1735 features an N-channel MOSFET pass transistor. Unlike similar designs using NPN bipolar pass transistors, N-channel MOSFETs require extreme- ly low drive currents, reducing overall quiescent cur- rent. Also, NPN-based regulators consume still more base current in dropout conditions when the pass tran- sistor saturates. The MAX1735 does not suffer from these problems, consuming only 125µA total current at full load and in dropout. Output Voltage Selection The MAX1735 features Dual Mode operation, allowing for a preset or adjustable output voltage. In preset voltage mode, the output of the MAX1735 is set to -5.0V, -3.0V, or -2.5V (see Ordering Information). Select this mode by connecting SET to GND (Figure 2). ON OFF ON THERMAL SENSOR NMOS PASS TRANSISTOR OUT COUT R1 R2 SET GND Dual Mode COMPARATOR ERROR AMPLIFIER VREF -1.25V -270mV SHUTDOWN LOGIC SHDN CIN IN MAX1735GND Figure 1. Functional Diagram 6 _______________________________________________________________________________________

Page 8

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 _______________________________________________________________________________________ 7 In adjustable mode, an output voltage between -5.5V and -1.25V is selected using two external resistors connected as a voltage-divider from OUT to SET (Figure 3). The out- put voltage is determined by the following equation: where VSET = VREFERENCE = -1.25V when in regulation. Since the input bias current at SET is <100nA, use large resistance values for R1 and R2 to minimize power consumption in the feedback network. A typical value of 100kΩ for R2 is acceptable for most applica- tions. Higher values consume less current at the expense of output voltage accuracy. The above equa- tion solved for R1 is: For preset output voltage mode, connect SET directly to GND. Shutdown In shutdown, the N-channel MOSFET, control circuitry, reference, and all internal circuits are turned off, reduc- ing supply current to typically 1nA. SHDN can be dri- ven by either a positive or negative voltage. Drive SHDN above +1.6V or below -1.6V to turn the regulator on. To turn the regulator off, drive SHDN to GND. For always-on operation, connect SHDN to IN. By including a positive threshold at SHDN, it can be driven by a standard 5V TTL level without needing level-shifting cir- cuitry. Current Limiting The MAX1735 features a current limit that protects the regulator. Short-circuit output current is typically 515mA. The output will withstand a short to ground indefinitely; however, if the increased power dissipation heats the die to +160°C, the thermal overload protec- tion will shut off the regulator, preventing damage to the IC. Thermal Overload Protection The thermal overload protection circuit protects the reg- ulator against overheating due to prolonged overload conditions. When the die temperature exceeds +160°C, an on-chip thermal sensor disables the pass transistor, allowing the IC to cool. The thermal sensor reenables the pass MOSFET once the die temperature drops 15°C. A continuous short-circuit fault condition results in a cyclical enabling and disabling of the output. Thermal overload protection is designed to safeguard the MAX1735 in the event of overload fault conditions. For normal operation, do not exceed the absolute maxi- mum junction temperature rating of +150°C. Junction temperature is greater than ambient by an amount depending on package heat dissipation and the ther- mal resistance from the junction to ambient (θJA): TJUNCTION = TAMBIENT + (θJA)(PDISSIPATION) where θJA for the 5-pin SOT23 is about 0.140°C/mW. R R V V OUT SET 1 2 1=     −         V V R R OUT SET= +          1 1 2 MAX1735 SHDN INPUT CIN 1µF CERAMIC ADJUSTABLE OUTPUT COUT 1µF CERAMIC OUTIN SET GND ON OFF ON -6.5V TO -2.5V GND -5.5V TO -1.25V R2 R1 VOUT = VSET (1 + R1)R2 Figure 3. Typical Application Circuit with Adjustable Output Voltage MAX1735 SHDN INPUT CIN 1µF CERAMIC FIXED OUTPUT COUT 1µF CERAMIC OUTIN SET GND ON OFF ON -6.5V TO -2.5V GND -5.0V,-3.0V, OR -2.5V Figure 2. Typical Application Circuit with Preset Output Voltage

Page 9

M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 8 _______________________________________________________________________________________ Operating Region and Power Dissipation Maximum power dissipation of the MAX1735 depends on the thermal resistance of the case and the circuit board, the temperature difference between the die junction and ambient air, and the rate of air flow (see also Thermal Overload Protection). The maximum power that can be dissipated by the device is: where the numerator expresses the temperature differ- ence between the maximum allowed die junction (+150°C) and the surrounding air, θJC (junction to case) is the thermal resistance of the package, and θCA (case to ambient) is the thermal resistance from the package through the PC board, traces, and other material to the surrounding air. The former is a characteristic solely of the device in its package, and the latter is completely defined by PC board layout and airflow. It is important to note that the ability to dissipate power is as much a func- tion of the PC board layout and air flow as the packaged part itself. Hence, a manufacturer can reliably provide a value for θJC, but not accurately provide a value for the total thermal resistance θJA. θJA is the sum of θJC and θCA, and the manufacturer can seldom reliably predict the thermal characteristics of the application circuit. Figure 4 shows the estimated allowable power dissipa- tion for a MAX1735 mounted on a typical PC board at ambient temperatures of +50°C, +70°C, and +85°C. Figure 4 shows the maximum continuous output current for a particular input-to-output voltage differential, for selected ambient temperatures. The working principle is that the SOT23-5 package is small enough that in a typi- cal application circuit at room temperature, the package cannot dissipate enough power to allow -6.5V to be reg- ulated to -1.25V at -200mA output (more than 1200mW). As ambient temperature falls, the available power dissi- pation increases to allow for a greater operating region. The equation for the family of curves follows: where |IOUT| is in mA, |VOUT - VIN| in V, PMAX (571mW) is the absolute maximum rated power dissipation at +70°C for the SOT23-5, and θJA (0.140°C/mW) is the approximate junction-to-ambient thermal resistance of the SOT23-5 in a typical application. A key to reducing θCA, thereby increasing thermal con- ductivity to the PC board, is to provide large PC board pads and traces for IN. __________Applications Information Capacitor Selection and Regulator Stability Capacitors are required at the input and output of the MAX1735. Connect a 1µF or greater capacitor between IN and GND. This input capacitor serves only to lower the source impedance of the input supply in transient conditions; a smaller value can be used when the regu- lator is powered from a low-impedance source, such as another regulated supply or low-impedance batteries. For output voltages between -2.5V and -5.5V, connect a 1µF or greater capacitor between OUT and GND. For voltages between -1.25V and -2.5V, use a 2.2µF or greater output capacitor. The maximum value of the output capacitor to guarantee stability is 10µF. The output capacitor’s value and equivalent series resistance (ESR) affect stability and output noise. To ensure stability and optimum transient response, output capacitor ESR should be 0.1Ω or less for output volt- ages from -1.25V to -2.45V and 0.2Ω or less for output voltages between -2.5V and -5.5V. Inexpensive sur- face-mount ceramic capacitors typically have very-low ESR and are commonly available in values up to 10µF. Other low-ESR capacitors, such as surface-mount tan- talum, may also be used. Do not use low-cost alu- minum electrolytic capacitors due to their large size and relatively high ESR. Lastly, make sure the input and output capacitors are as close to the IC as possible to minimize the impact of PC board trace impedance. | | | | I P T V V OUT MAX A JA OUT IN = − − − 70 θ P T T T T MAX JMAX A JC CA JMAX A JA = − + = − θ θ θ 250 150 100 50 0 0 31 2 4 5 6 MAXIMUM OUTPUT CURRENT vs. INPUT-OUTPUT VOLTAGE DIFFERENTIAL INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V) M A X IM U M O U TP U T C U R R EN T (m A ) D EV IC E IN D R O P O U T M A X S U P P LY V O LT A G E – M IN O U TP U T V O LT A G E AT MAXIMUM JUNCTION TEMP (TJ = +150°C) 200 MAXIMUM CONTINUOUS CURRENT T A = +50°C T A = +70°C T A = +85°C Figure 4. Output Current and In-Out Voltage Differential Operating Region Bounded by Available Power Dissipation at Selected Ambient Temperatures

Page 10

Noise, PSRR, and Transient Response MAX1735 output noise is typically 160µVRMS. This is suitably low for most applications. See the Output Noise vs. Frequency plot in the Typical Operating Characteristics. The MAX1735 is optimized for battery-powered equip- ment, with low dropout voltage and low quiescent cur- rent. It maintains good transient response, AC rejection, and noise characteristics even near dropout. See Power-Supply Rejection Ratio vs. Frequency in the Typical Operating Characteristics. When operating from very noisy sources, supply noise rejection and transient response can be improved by increasing the input and output capacitance, and by employing pas- sive postfiltering. Dropout Voltage A regulator’s minimum input-to-output voltage differen- tial dropout voltage determines the lowest usable sup- ply voltage for an application. In battery-powered systems, this determines the useful end-of-life battery voltage. Since the MAX1735’s pass element is an N-channel MOSFET, dropout voltage is the product of RDS(ON) and the load current; see Electrical Characteristics and Dropout Voltage vs. Load Current in the Typical Operating Characteristics for details. The MAX1735 operating (ground pin) current typically remains below 125µA at full load in dropout. ___________________Chip Information TRANSISTOR COUNT: 293 M A X 1 7 3 5 200mA, Negative-Output, Low-Dropout Linear Regulator in SOT23 _______________________________________________________________________________________ 9

MAX1735EUK25+T Reviews

Average User Rating
5 / 5 (105)
★ ★ ★ ★ ★
5 ★
4 ★
3 ★
2 ★
1 ★

Write a Review

Not Rated
Thanks for Your Review!


July 16, 2020

I enjoy Good service from Heisener team , I can get good quality components what I want in


July 10, 2020

Great price. Worked well for my needs.


June 28, 2020

These did exactly what I needed them to do. Electricity only flows in one direction. Perfect.


June 25, 2020

EXACTLY what I was looking for -- one piece with a low forward voltage drop to isolate some DC power sources. They work fantastic!


June 23, 2020

Good seller, incredible reliable.Item as described. Very professional


June 13, 2020

Website and order clear, concise and user friendly. Thanks!


June 5, 2020 is a good company. Pleasant transaction, communicative , thank you


June 3, 2020

These little guys worked perfect for my wiring project. Reliable, good quality.


June 2, 2020

fast delivery and good product, very happy


May 31, 2020

There are cheaper ones out there but this one really take the guessing game out.

MAX1735EUK25+T Guarantees

Service Guarantee

Service Guarantees

We guarantee 100% customer satisfaction.

Our experienced sales team and tech support team back our services to satisfy all our customers.

Quality Guarantee

Quality Guarantees

We provide 90 days warranty.

If the items you received were not in perfect quality, we would be responsible for your refund or replacement, but the items must be returned in their original condition.

MAX1735EUK25+T Packaging

Verify Products
Customized Labels
Professional Packaging

MAX1735EUK25+T Related Products

SIT1602AI-12-33E-74.250000E SIT1602AI-12-33E-74.250000E SiTIME, OSC XO 3.3V 74.25MHZ, 4-SMD, No Lead, - View
2220Y5K00330KCT 2220Y5K00330KCT Knowles Syfer, CAP CER 2220, -, - View
PIC32MX570F512HT-I/MR PIC32MX570F512HT-I/MR Microchip Technology, IC MCU 32BIT 512KB FLASH 64QFN, 64-VFQFN Exposed Pad, - View
Y006225R0000F0L Y006225R0000F0L Vishay Foil Resistors (Division of Vishay Precision Group), RES 25 OHM 0.6W 1% RADIAL, Radial, - View
RNC50J4991DSB14 RNC50J4991DSB14 Vishay Dale, RES 4.99K OHM 1/10W .5% AXIAL, Axial, - View
EEC35DRYN-S93 EEC35DRYN-S93 Sullins Connector Solutions, CONN EDGE DUAL FMALE 70POS 0.100, -, - View
HM2R71PA5108N9 HM2R71PA5108N9 Amphenol FCI, CONN RECEPT 95POS TYPE B R/A, -, - View
V24C28H150B3 V24C28H150B3 Vicor Corporation, CONVERTER MOD DC/DC 28V 150W, Quarter Brick, - View
MI-J5J-IA-F4 MI-J5J-IA-F4 Vicor Corporation, DC/DC CONVERTER 36V 10W, 9-DIP Module, - View
V48C28H75BS V48C28H75BS Vicor Corporation, CONVERTER MOD DC/DC 28V 75W, Quarter Brick, - View
VI-25J-EX-F3 VI-25J-EX-F3 Vicor Corporation, CONVERTER MOD DC/DC 36V 75W, Full Brick, - View
VI-BT4-EW-F4 VI-BT4-EW-F4 Vicor Corporation, CONVERTER MOD DC/DC 48V 100W, Full Brick, - View
Payment Methods
Delivery Services

Quick Inquiry


Certified Quality

Heisener's commitment to quality has shaped our processes for sourcing, testing, shipping, and every step in between. This foundation underlies each component we sell.

ISO9001:2015, ICAS, IAF, UKAS

View the Certificates

Do you have any question about MAX1735EUK25+T?

+86-755-83210559 ext. 811 heisener007 2354944915 Send Message

MAX1735EUK25+T Tags

  • MAX1735EUK25+T
  • MAX1735EUK25+T PDF
  • MAX1735EUK25+T datasheet
  • MAX1735EUK25+T specification
  • MAX1735EUK25+T image
  • Maxim Integrated
  • Maxim Integrated MAX1735EUK25+T
  • buy MAX1735EUK25+T
  • MAX1735EUK25+T price
  • MAX1735EUK25+T distributor
  • MAX1735EUK25+T supplier
  • MAX1735EUK25+T wholesales

MAX1735EUK25+T is Available in